Free Software and Maths!
Over 10 years ago we started posting free software and mathematics so people could make themselves a very basic roulette computer that would work for free! We was the only genuine commercial roulette computer seller and rental supplier. The information below shows how mathematics can beat roulette by taking timings of the ball and rotor. We had made enough money with our devices and decided to give our maths and software away, but sell basic hardware(a few hundred dollars) and rent our devices to prove they worked! We did not realize that criminals would set up shop using our technology and software and free mathematics claiming to have better products than our own and selling them for over inflated prices for thousands of dollars and refusing to rent them.
Here is some free mathematics, enjoy!
The formula (polynomial for the data) can be obtained by taking three lots of timings, with associated times of distance that corespond to these timings or the distances!
First of all, the data you need from your timings must be spread over a large spread of the data so that you are interpolating rather than extrapolating!
So first of all you need to write down some timings, one after the other, plus an associated time of distance with each data set. So basically an example would be the following>
Times of each rev 10 11 13 15 18 21 25 28 35 42
Timing
Time of distance 207 197 184 169 151 130 105 77 42 0
with these timings
Distance associated 9 8 7 6 5 4 3 2 1 0
with these Timings
So an example would be the number 13 for a rev timing. we know now that it will take 184 units of time to drop and it will have taken 7 full revolutions!
But obviously we need to know what will happen if we get a timing of say 14 units or 23 units. This is where the polynomial comes in!
So we need three sets of data to predict the timing, and three sets of data to produce the distance!
Lets call these X(1), X(2), X(3) Y(1),Y(2),Y(3)
And we need to take a spread over a large data set, so using the above data we will take three timings , one at the begining, one in the middle, and one at the end! Our timings of the revolution will always be in either the time of distance calc or the Distance calc.
So first we will do the Time of distance, so lets take the data from above>
X(1)=10 X(2)=18 X(3)=35 (Times of revolutions)
Y(1)=207 Y(2)=151 Y(3)=42 (times of corresponding times of distance)
Place this data in the following formula>
Formula:
a=(X(2)*X(2))-(X(1)*X(1))
b=(X(3)*X(3))-(X(2)*X(2))
c=(X(2)-X(1))
d=(X(3)-X(2))
e=(Y(2)-Y(1))
f=(Y(3)-Y(2))
g=((c*f)-(d*e))/((b*c)-(a*d))
h=(Y(1)-(g*(X(1)*X(1))))
i=(Y(2)-(g*(X(2)*X(2))))
j=((i-h)/X(2)-X(1)))
k=Y(1)-(X(1)*(X(1)*g)-(X(1)*j)
This works out a 2nd order polynomial!
Which is the module ‘Formula’ in the program on the Psion. You can use a calculator, or get the Psion to do it!
From this you want the numbers that correspond to g,j and k. These are the three functions to go into your equation.
Now enter another number in the following formula>
we will call your number Z
Time of Distance for any given number = ((Z*Z)*g)+(Z*j)+k
So if you enter 21 for the value of Z, you should get 130 for Time of distance!
Enter an intermediate value such as 23 and the formula will give you the distance travelled and the number of revolutions travelled, this will then correspond to observed data later!
To get the distance using the same formula, leave the value of X(1), X(2),X(3) the same, just change the values of Y(1) etc to the associated numbers of revolutions at the top, then do the formula again! This time the formula will give you the distance for any given time of revolution!
This information was posted all over the Internet by us to prove we was genuine nearly 10 years ago , check out the links yourselves!
http://www.casinoportalen.dk/forum/thread.asp?id=9489
http://www.gamblersglen.com/cgi-bin/teemz/teemz.cgi?board=_master&action=opentopic&forum=Roulette_Archive&topic=79
Several weeks ago we distributed some free code on this site of our Roulette computers and our PDA systems. This was to show how in part some of our programs worked, not one of them was a fully working program that could be used in a casino or modified. Unfortunately illegal twisted operator Steven Hourmouzis decided to to advertise this software to attempt to prove our devices did not work in some crooked way and altered the code to totally make it ineffective in every area. Please be aware of this and if you want the original code, just ask me. The Ineffective programs are called Fastroul, SectorV, P1, etc, everyone knows our good feedback through Ebay and knows this is not what our workable computer software is called! There is some crazy people on the internet, so be careful! Software is no good without modified hardware to enable stealth play and the correct software instructions. Do not RISK playing with this software, its been corrupted deliberately by us to show you our programming capabilities and that we are genuine.
We also have basic free roulette maths advertised on our sites if you wish to go down the road of developing your own roulette computer and will help you do this if you wish to be a little adventurous and develop your own hardware!
£10,000 reward for anyone supplying information that will lead to the fool that is claiming to have our software for free which has been corrupted. This could cause you to lose money asits not the fullcorrect program, so be careful! Westart supplying roulette computer for just 10% deposit (£220) and you recieve the full kit, no other competitor does this, because they wish to sting you for as much money as they can in one go before you find out their equipment does not work!